visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model p d 0 9 2 2 j 7575 d2 hf rev b ultra low profile 0805 power divider 75 to 75 description the PD0922J7575D2HF is a low profile, subminiatur e wilkinson power divider in an easy to use surface mount package and is ideal f or high volume manufacturing while delivering higher performances than tradition al printed and lumped element solutions. it has been designed for the following m arkets: dvbs, gsm, dcs, pcs, wcdma, gps, 802.11a+g, bluetooth, and zigbee usa. the PD0922J7575D2HF is matched to 75 and has a height profile of 0.8 mm. a two section wilkinson design results in increased i solation performance. two external resistors are required for operation. com ponents are available on tape and reel for high volume manufacturing pick and place. detailed electrical specifications: specifications subject to change without notice. room (25 c) parameter min. typ. max unit frequency 950 2150 mhz input port impedance 75 output port impedance 75 return loss 9.5 11 db insertion loss* 0.8 1.0 db amplitude balance 0.4 0.7 db phase balance 2 3 degrees isolation (output ports) 14 16 db power handling 2 watts features: ? 950 C 2150 mhz ? 16 db isolation (output ports) ? good return loss ? 0.8mm height profile ? 75 outputs/inputs ? external resistors required ? low insertion loss ? surface mountable ? tape & reel ? nonconductive surface ? rohs compliant ? halogen free operating temperature 55 +85 oc * insertion loss stated at room temperature (insert ion loss is approximately 0.1 db higher at +85 oc) outline drawing designation output 1 input mid 2 mid 1 gnd output 2 5 4 2 16 3 pin 2.040.10 1.290.10 0.810.08 1 2 3 6 5 6x 0.30 mechanical outline dimensions are in millimeters 4x 0.37 6x 0.22 4x 0.65 6x 0.98 orientation marker denotes pin location 4 orientation marker denotes pin location top view (near side) side view bottom view (far side) 2x 0.15
visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model p d 0 9 2 2 j 7575 d2 hf rev b typical broadband performance: 500 mhz. to 8.0 ghz. return loss input 36 33 30 27 24 21 18 15 12 9 6 3 0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 frequency [mhz] [db] insertion loss 36 33 30 27 24 21 18 15 12 9 6 3 0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 frequency [mhz] [db] amplitude balance 2 1.5 1 0.5 0 0.5 1 1.5 2 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 frequency [mhz] [db] phase balance 20 15 10 5 0 5 10 15 20 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 frequency [mhz] deg isolation 36 33 30 27 24 21 18 15 12 9 6 3 0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 frequency [mhz] [db]
visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model p d 0 9 2 2 j 7575 d2 hf rev b typical performance: 900 mhz. to 2200 mhz. return loss input 36 33 30 27 24 21 18 15 12 9 6 3 0 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 frequency [mhz] [db] insertion loss 3.6 3.3 3.0 2.7 2.4 2.1 1.8 1.5 1.2 0.9 0.6 0.3 0.0 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 frequency [mhz] [db] amplitude balance 2 1.5 1 0.5 0 0.5 1 1.5 2 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 frequency [mhz] [db] phase balance 20 15 10 5 0 5 10 15 20 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 frequency [mhz] deg isolation 36 33 30 27 24 21 18 15 12 9 6 3 0 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 frequency [mhz] [db]
visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model p d 0 9 2 2 j 7575 d2 hf rev b mounting configuration: in order for xinger surface mount components to wor k optimally, the proper impedance transmission line s must be used to connect to the rf ports. if this condition is not satisfied, insertion loss, isolation and vs wr may not meet published specifications. all of the xinger components are constructed from o rganic ptfe based composites which possess excellen t electrical and mechanical stability. xinger compone nts are compliant to a variety of rohs and green st andards and ready for pbfree soldering processes. pads are gol d plated with a nickel barrier. an example of the pcb footprint used in the testing of these parts is shown below. in specific designs , the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. in addition, s ince the PD0922J7575D2HF is a wilkinson power divid er, external 0402 15 0 and 300 resistors must be mounted in locations r1 and r2 respectively, as shown in the figure below. pad footprint w/ 0402 resistor locations 6x .41 6x .33 .04 4x .25 .66 plated thru holes to ground 3x transmission lines r2 r1 circuit pattern footprint pad (s) solder resist mounting footprint dimensions are in millimeters
visit us at www.anaren.com usa/canada: toll free: europe: asia: (315) 4328909 (800) 4116596 +44 2392232392 +86 51262749282 model p d 0 9 2 2 j 7575 d2 hf rev b packaging and ordering information parts are available in reel and are packaged per ei a 4812. parts are oriented in tape and reel as sh own below. minimum order quantities are 4000 per reel. see model numbers be low for further ordering information . .25 2.41 1.00 8.00 4.00 2.00 1.75 3.50 4.00 1.60
|
